Why Xerox WorkCentre 3210N printer needs to be reset:
– Xerox WorkCentre 3210N printer’s cartridge is enclosed with a toner chip that was used to calculate toner coverage and to deliver bold or light printout quality depending on printer original printout design.
– Xerox WorkCentre 3210N printer toner chip contains calculated limitation that was managed by Xerox manufacturer. Following Xerox, if toner coverage is 5%, Xerox WorkCentre 3210N printer toner chip is delivered 2.000 – 5.500 pages.
– If toner coverage is higher than 5% -> Toner Page Yields are less than “2.000 – 5.500″ pages. If toner coverage is lower than 5%, Toner Page Yields are “2.000 – 5.500″ pages. That is the reason why bold printouts (high toner coverage) will make printer run out of toner quickly.
– When Xerox WorkCentre 3210N printer toner chip overload its calculated limitation, printer will be locked inspire of high toner cartridge.
When Xerox WorkCentre 3210N printer needs to be reset:
– Xerox WorkCentre 3210N printer’s messages: red light blinking, imprinting.
– Computer’s messages: empty toner, Replace toner, install toner, end of life replace new cart , toner cartridge is not installed, Install the cartridge, toner exhausted.
How to fix Xerox WorkCentre 3210N printer with imprinting error:
1. Change new toner cartridge:
Toner Cartridge Xerox WorkCentre 3210N printer
– Xerox WorkCentre 3210N printer’s toner cartridge (Xerox 106R01485,Xerox 106R01486 Toner Cartridge) costs $80 – $110 depending on its supplier and manufacturer.
– Changing toner cartridge seems to be suboptimal because when printer runs out of toner, we also need to change new toner cartridge => money wasting
2. Change new toner chip:
Toner chip Xerox WorkCentre 3210N printer
– Xerox WorkCentre 3210N printer’s toner chip costs $6 – $10 depending on its supplier.
– Changing toner chips seems to be more optimal but when printer runs out of toner, we also need to change new toner chip.
3. Reset Xerox WorkCentre 3210N printer by using software:
Firmware fix Xerox WorkCentre 3210N printer
– Xerox WorkCentre 3210N printer’s reset software costs $12 USD.
– Reset software automatically impacts to printer firmware so printer ignores paper counter. Therefore, there is not necessary to change toner chip, you just refill toner when it runs out.
Xerox WorkCentre 3210N printer reset software introduction:
– Product name: Xerox WorkCentre 3210N printer reset software.
– Compatible printer: Xerox WorkCentre 3210N printer.
– Compatible versions: 95f, .99f // SN + 6 dots, .99f // SN + 5 dots, .98f // SN + 5 dots, .01f // SN + 5 dots.
Notes before resetting Xerox WorkCentre 3210N printer:
– Identify accurate version, serial and crum of Xerox WorkCentre 3210N printer.
– Printer’s Driver is installed on computer.
– Check the connection between computer and printer to make sure it works well.
– Toner chip located over the cartridge is removed or covered by tapes.
– Remove connection gates such as USB gate, LPT gate from computer (Except for printer, keyboard, mouse).
– Make sure the electric power works well during soft-ware running process (you should use UPS for printer and computer to prevent them from loosing electric power).
When you are running firmware, do not install the manufacturer’s firmware because this firmware is displacement. If you are wrong in one of those beyond rules, your printer can be meet faulty problems and can not be recovered to the original status.
How to reset Xerox WorkCentre 3210N printer:
1. Connect computer to printer by usb cable.
2. Turn printer on and wait until it is ready for working.
3. Run “download.bat”(or drag and drop *.hd file to usbprns2.exe file) file on computer.
4. “download.bat” file program will automatically run printer’s firmware. After automatic set up process, printer will be restarted by itself.
5. Restart printer one more time -> in test